Digi Device Setup Wizard Driver Support For
Digi Device Setup Wizard Driver Software Is
Digi Device Setup Wizard Download The Latest

In that case, insert the device and click the Refresh Selection button.

The hardware consists of an evaluation board (DS9120P) with RJ1 1 cable, a Maxim 1-Wire adapter module (DS9481R-3C7) that connects the board to the PC, and a DS28E05 in a TSOC package.

The DS28E05 features 1 12 bytes of user memory organized as seven pages of 16 bytes.

Each page can be write-protected or set into EPROM emulation mode.

The evaluation software runs under Windows 8, Windows 7, Windows Vista, or Windows XP, providing a handy user interface to exercise the features of the DS28E05.

Digi Device Setup Wizard Driver Support For

Features Driver Support for Windows 8, Windows 7, Windows Vista, and Windows XP Fully Compliant with USB Specification v2.0 USB Powered with No External Power Supply Required USB to 1-Wire Adapter Utilizes Both the Prolific PL-2303HXD and the Maxim DS2480B Emulator to Create a Virtual COM-to-1-Wire Port on Any PC Accommodates TSOC Package IC 1-Wire is a registered trademark of Maxim Integrated Products, Inc.

Rev 0; 115 Ordering Information appears at end of data sheet.

Quick StartDriver Installation See Figure 1 for a photo of the stand-alone EV board with RJ1 1 cable and Figure 2 for a photo of the 1-Wire adapter with USB cable that plugs into the PC.

Required Equipment DS9481R-3C7 1-Wire adapter with USB cable DS9120P EV board with RJ1 1 cable DS28E05 in a TSOC package PC with a Windows 8, Windows 7, Windows Vista, or Windows XP operating system and a spare USB port T able 1.

Required Hardware for PC Evaluation Denotes a lead(Pb)-freeRoHS-compliant package.

P ART QTY DESCRIPTION DS9120P 1 EV board with RJ1 1 cable DS9481R-3C7 1 1-Wire USB adapter with USB cable DS28E05 5 in a TSOC package Figure 1.

T ext in bold refers to items directly from the EV kit software.

T ext in bold and underlined refers to items from the Windows operating system.

Before connecting to the PC, follow the steps below to verify board operation: 1) Insert the DS28E05 in the TSOC socket on the DS9120P EV board.

Connect the DS9120P EV board to the DS9481R-3C7 1-Wire adapter with the RJ1 1 cable.

Do not insert the DS9481R-3C7 into the PC at this time.

Digi Device Setup Wizard Driver Software Is

This should be done in step 12, after all driver software is installed.

Digi Device Setup Wizard Download The Latest

T o install the PL-2303HX Prolific Driver (for the DS9481R-3C7), visit - liopl2303hx-rev-d-usb-to-serial-bridge-controller to download the latest version of the Prolific Windows Driver Installer Setup Program, PL2303Prolific DriverInstallerv190.zip.

Unzip the archive and Run the executable file that begins with PL2303ProlificDriverInstaller.

Follow the directions of the Install Wizard until the PL-2303 USB-to-serial driver installation is finished.

Close by clicking the Finish button.

Visit www.maxim-ic.com1-wiredrivers to down- load and install the 1-Wire Drivers software package.

When prompted with the question Do you want to run or save this file, select Run.

When you get a security warning that asks Do you want to run the software, select Run.

Read and check the box if you accept the license agreement and click Install.

Click the Finish button to exit the Setup Wizard.

Microsoft.NET Framework V ersion 3.5 SP1 or newer is required for the program to run.

T o check whether it is installed, look in the Control Panel under Pro- grams and Features.

If.NET is not listed, it is not installed.

For download and installation instructions, go to www.microsoft.comen-usdownloaddetails.

Insert the DS9481R-3C7 into a spare USB port on the PC.

Determine the COM port by looking in Control Panel System Hardware tab Device Manager and expand Ports (COM LPT).

See Figure 3. Quick StartSoftware Setup After downloading the software from the URLs listed in the previous Quick Start section, and unzipping and saving the files to a folder, start the EV kit software by double-clicking the file DS28E05EvaluationProgram.

Figure 3. DS9481R-3C7 COM Port.

The Adapter Port is a COM port mapped by the Prolific device.

Click on the Open AdapterPort button or on the Auto-Search button.

If successful, the Status field next to the Open AdapterPort but- ton displays Success.

The device selection options are displayed in the Device Selection Methods group box in the Setup tab.

The default setting for the EV kit software is Match- ROM in the ROM Selection Method drop-down list.

Also, the Use Search-ROM to find the first avail - able EV kit device is checked by default.

Retain these default selections for quick setup.

Once the adapterport has been opened, the DS28E05 Device Selection drop-down list is automatically populated with the unique ROM ID of the available DS28E05s.

Digi Device Setup Wizard Windows 7